|
Product Details:
|
| Pump: | Grundfos Pump | Shaft Diameter: | 12mm 16mm |
|---|---|---|---|
| Secondary Sealing: | NBR/EPDM/Fkm | Material: | Carbon, Ceramic, NBR |
| Origin: | Guangzhou, China | Installation: | Easy To Install |
| Highlight: | 10k27 Grundfos Pump Mechanical Seal,G3 Grundfos Pump Mechanical Seal,16mm 10k27 mechanical seal |
||
10k27 Grundfos Pump Mechanical Seal G3-12mm CHI 2/4 G3-16mm
mechanical Shaft Seal Kit BQQEBUBE 12mm for TP NP submersible pump
Widely used in CH,CHI,CHE,CRK,SPK,TP,AP series pump
CR,CRN, NK,TP series pump
LM(D)/LP(D),NM/NP,DNM series pump
And our seal can replace the original one.
Our seals are high-qualified due to we strictly follow theDIN24960.ISO3069,EN12756.AP1628 standards.
If the seal is not the one you need, contact us andinform us your pump model or drawing, material, shaftsize for quotation.
Ne will advise you and offer you corresponding
mechanical seals.
Customized products and OEM is welcomed.
We offer factory price, high quality, fast delivery and bestservices.
Application water pump model pairing table
|
Seal size d(mm) |
d3 | d6 | d7 | 11 | 13 |
|
12 16 |
22 26 |
19 23 |
23 27 |
39.0 39.0 |
7.6 8.7 |
Technical Parameters
| Temperature | -30℃~+150℃ |
| pressure | ≤0.3Mp a |
| Speed | ≤4500r/mim |
| Medium | Clean water |
Materials
| Rotary Ring |
SiC/TC |
| Stationary Ring |
Carbon/SiC/TC |
| Spring | SUS304/SUS316 |
| Stationary Seat | SUS304/SUS316 |
| Secondary Seal |
NBR/EPDM/Fkm |
| Rotary Ring Holder | SUS304/SUS316 |
Preperation:
1. Shaft Outside Diameter is within tolerance +-0.05mm
2. Shaft run out <0.1mm
3. Shaf end float <0.13mm
4, No sharp edges on the shaft over the o ring
Note:
During the installation,don't scratch or damage the o ring.lf anything is damaged,please contactwith Us to replace a new one.
Installation in strucstions:
1. The full set of cartridge seal is cleaned and exactly passed leakage examine before sale.Inorder to avoid damage,don't disassemble and clean the parts again before fixing.
2 The fitting allowance between the seal and shaft is dl h6 0.8,and there should be leading-inedge at the end of shaft.The outside diameter of shaft at the position of screw should be 01 0.2mm smaller,resisting the screw over-tighten.Lubricate the shaft with oil
3. Place the cartridge seal into the pump chamber,then:
A: Tighter four screw bolts of flanges,ensuring the medium leading in hole"G"at the top Position
B : Tighter four set screws and position the shaft sleeve on the shaft.
C: Remove four gauge plates.Please keep them and they wil be used in future installation and
disassemble.
D: Connect the medium lead_in pipe with hole"G"in order to flush away the friction heat and
flushing the seal chamber when pump running.
Note:
ter complete the installation,turning the shaft by hand to check for the rotationi he shat could not rotate smoothily,seal had been improperly installed.
We would like lo sincerely ooperale with Clients to supply high qually products and senice We beleve in establishing a long:erm cooperalive relalionshipis lhe key to suceess
Contact Person: ZENG
Tel: +8617620005542
